POLY-TAC is an industrial strength, contact spray adhesive formulated for bonding Expanded Polystyrene Foam (EPS) to itself and many other materials. POLY-TAC can be sprayed directly onto EPS surfaces without damaging the foam. Superior bond strength properties and exceptional tack make POLY-TAC an excellent choice for permanent bonding of EPS.
COMMON USES
Bonds Rigid Insulation Panels, Tack Reinforcing Mesh to Foam, Bonds Polystyrene to a Variety of Substrates, Laminate Multicore Panels
Manufacture of Whiteboards, Set Building, Formwork Construction
BONDS
POLY-TAC will effectively bond polystyrene, urethane foam, particleboard, MDF, timber, concrete, carpet, felt, fabrics, paper products, duct insulation, steel, aluminium, moulded fiberglass, and many other materials.
ADVANTAGES
Polystyrene Safe
Heat Resistant
Multipurpose
Waterproof
No Ozone Depleting Substances
Low Odour
High Coverage
High Solids
Two Way Adjustable Nozzle
PREPARATION
For best results all surfaces to be bonded must be clean, dry and free from dirt, dust, oil, loose paint, wax and grease. The temperature of the adhesive and the surfaces being bonded should ideally be between 15°C - 27°C.
TECHNICAL DETAILS
Chemical Description: Solvent Based Contact Adhesive
Solids Content: 38 - 44%
Viscosity: Sprayable Grade
Minimum Open Time: 1 - 5 minutes
Maximum Open Time: 5 hours (best results within 1hr)
Heat Resistance: -40 – +85ºC
Cleaner: Citrus Cleaner or Acetone
Flash Point: -41ºC
Specific Density: 0.70kg per ltr +/- 5%
APPEARANCE
Blue Sprayable Liquid
ODOUR
Minimal Solvent Odour
CLEAN UP
Excess adhesive and overspray may be removed with CANTAC Citrus Cleaner, Acetone, WOODLOK GLAZE-AWAY & DSOLV-AWAY, GLUE GURU 05CR or most Industrial Solvents.
LIMITATIONS
POLY-TAC is not suitable for High Pressure Laminates (HPL). POLY-TAC is not recommended for Vinyl Flooring. TESTING Always test the suitability of the product for your application before use.
COVERAGE
5m2 per 575ml Aerosol Can, Single Sided (Guide only. Coverage depends on absorbency of surface and coating weight).
Login
COMMON USES
- Bonds Rigid Insulation Panels, Tack Reinforcing Mesh to Foam, Bonds Polystyrene to a Variety of Substrates, Laminate Multicore Panels
- Manufacture of Whiteboards, Set Building, Formwork Construction
BONDSPOLY-TAC will effectively bond polystyrene, urethane foam, particleboard, MDF, timber, concrete, carpet, felt, fabrics, paper products, duct insulation, steel, aluminium, moulded fiberglass, and many other materials.
ADVANTAGES
- Polystyrene Safe
- Heat Resistant
- Multipurpose
- Waterproof
- No Ozone Depleting Substances
- Low Odour
- High Coverage
- High Solids
- Two Way Adjustable Nozzle
PREPARATIONFor best results all surfaces to be bonded must be clean, dry and free from dirt, dust, oil, loose paint, wax and grease. The temperature of the adhesive and the surfaces being bonded should ideally be between 15°C - 27°C.
TECHNICAL DETAILS
- Chemical Description: Solvent Based Contact Adhesive
- Solids Content: 38 - 44%
- Viscosity: Sprayable Grade
- Minimum Open Time: 1 - 5 minutes
- Maximum Open Time: 5 hours (best results within 1hr)
- Heat Resistance: -40 – +85ºC
- Cleaner: Citrus Cleaner or Acetone
- Flash Point: -41ºC
- Specific Density: 0.70kg per ltr +/- 5%
APPEARANCE- Blue Sprayable Liquid
ODOURCLEAN UP
Excess adhesive and overspray may be removed with CANTAC Citrus Cleaner, Acetone, WOODLOK GLAZE-AWAY & DSOLV-AWAY, GLUE GURU 05CR or most Industrial Solvents.
LIMITATIONS
POLY-TAC is not suitable for High Pressure Laminates (HPL). POLY-TAC is not recommended for Vinyl Flooring. TESTING Always test the suitability of the product for your application before use.
COVERAGE
5m2 per 575ml Aerosol Can, Single Sided (Guide only. Coverage depends on absorbency of surface and coating weight).
SIZES
TECHNICAL DATA SHEET
A Material Safety Data Sheet will be supplied upon request, please click here ...